DGABK datasheet, DGABK pdf, DGABK data sheet, datasheet, data sheet, pdf, Intersil, Quad SPST, CMOS Analog Switches. DGABK Datasheet, DGABK PDF, DGABK Data sheet, DGABK manual, DGABK pdf, DGABK, datenblatt, Electronics DGABK. DGABK datasheet, DGABK circuit, DGABK data sheet: MAXIM – Quad SPST CMOS Analog Switches,alldatasheet, datasheet, Datasheet search site.
|Published (Last):||2 September 2015|
|PDF File Size:||10.9 Mb|
|ePub File Size:||18.21 Mb|
|Price:||Free* [*Free Regsitration Required]|
DGABK Datasheet, PDF – Alldatasheet
An enable input is provided. In case of conflict between English and Metric dimensions, the inch dimensions control. VO is the steady state output with switch on.
For more information on TYP values see Note 3.
DGABK Datasheet(PDF) – Maxim Integrated Products
Limit diode current to maximum current ratings. Feedthrough via gate capacitance may result in dg201bk at leading and trailing edge of output waveform. Parameter guaranteed by design or characterization. Documents Flashcards Grammar checker. SR Datasheet – Micropower Direct. For the latest package outline information, go to www.
However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. A notch or a pin one identification mark shall be located adjacent to pin one and shall be located within the shaded area shown.
When the enable input is high, a channel is selected by the address inputs, and when low, all channels are dg201bak. Typical values are for design aid only, not guaranteed and not subject to production testing.
Accordingly, the reader is cautioned to ddatasheet that data sheets are current before placing orders. For more information on TYP values see Note 2. In either case, source-to-body diodes can be forward biased and conduct current from the signal source. Lab 6 in this note. Dimension M applies to lead plating and finish thickness.
Package Information continued The package drawing s in this data sheet may not reflect the most current specifications. Maxim reserves the right to change the circuitry and specifications without notice at any time. For this configuration dimension b3 replaces dimension b2.
The maximum limits datasheet lead dimensions b and c or M shall be measured at the centroid of the finished lead surfaces, when solder dip or tin plate lead finish is applied. Information furnished by Intersil is believed to be accurate and reliable. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied.
The algebraic convention whereby the most negative value is a minimum, and the most positive value is a maximum, is used in this data sheet. Copyright Intersil Americas Inc. This dimension allows for off-center lid, meniscus, and glass overrun. Putere n-am, Tu-mi fii sprijin. Device mounted with all leads soldered to PC board.
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. The addition of these diodes will reduce the analog signal range to 1V below the positive supply and 1V above the negative supply.
Selected parts for the query dg
The DG has a maximum turn-off time of ns and a maximum turn-on time of ns. All Rights Reserved All other trademarks mentioned are dztasheet property of their respective owners. Dambar protrusions datashset not exceed 0. Measure dimension S1 at all four corners. For information regarding Intersil Corporation and its products, see www. Maxim guarantees that these switches will not latch up if the power supplies are disconnected with input signals still connected.
Exposure to absolute maximum rating conditions for extended periods may affect device reliability. B1 maximum dimensions do not include dambar protrusions. Datashdet cum sunt, la Tine vin! Dimension Q shall be measured from the seating plane to the base plane. E and eA are measured with the leads constrained to be perpendicular to datum -C.
N is the maximum number of terminal positions. The DGA has a maximum turn-off time of ns and a maximum turn-on time of ns. No circuit patent licenses are ddg201abk. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Mold flash or protrusions shall not exceed 0. Pin Configurations continued To provide protection for overvoltages up to 20V above the supplies, a 1N or 1N dafasheet diode should be placed in series with the positive and negative supplies as shown in Figure 2.